Practice problems
Thevenin and Norton equivalent practice problems
Thevenin's theorem says any linear network of sources and resistors, seen from two terminals, acts like one voltage source Vth in series with one resistor Rth. These ten problems find Vth and Rth, then use them to get a load's voltage and current, the Norton current and the most power a source can deliver. Type your answer to check it, and open the working whenever you want it.
The method
- Vth: the output voltage with nothing connected
- Rth: short-circuit each voltage source, then find the resistance seen from the output. A divider's is R1 ∥ R2
- Norton: a current source IN = Vth ÷ Rth in parallel with the same Rth
- Most power goes into a load equal to Rth: P = Vth² over 4 Rth
The problems
Type your answer and tap Check. Every one has the working, step by step.
Problem 1 of 10
A divider has R1 = 6.8 kΩ on top and R2 = 3.3 kΩ on the bottom, across 12 V. What is the Thevenin voltage at its output?
Show the working
- Vth is the output with nothing connected: the plain divider formula.
- Vth = 12 V × 3.3 kΩ over 6.8 kΩ + 3.3 kΩ = 12 V × 3.3 over 10.1 ≈ 3.92 V
Answer: 3.92 V
Problem 2 of 10
The same divider (6.8 kΩ on top, 3.3 kΩ on the bottom, 12 V). What is its Thevenin resistance, in kilohms?
Show the working
- Short-circuit the 12 V source (replace it with a wire). Seen from the output, R1 and R2 now both connect to ground, so they're in parallel.
- Rth = 6.8 × 3.3 over 6.8 + 3.3 kΩ = 22.44 over 10.1 kΩ ≈ 2.22 kΩ
Answer: 2.22 kΩ
Problem 3 of 10
A circuit's Thevenin equivalent is a 5 V source in series with 1 kΩ. What voltage does a 4 kΩ load get?
Show the working
- Rth and the load make a new divider across Vth.
- Vload = 5 V × 4 kΩ over 1 kΩ + 4 kΩ = 5 V × 0.8 = 4 V
Answer: 4 V
Problem 4 of 10
A circuit's Thevenin equivalent is a 9 V source in series with 600 Ω. What current flows into a 300 Ω load, in milliamps?
Show the working
- The load sees one loop: Vth in series with Rth and the load.
- I = 9 V over 600 Ω + 300 Ω = 9 V over 900 Ω = 0.01 A, which is 10 mA.
Answer: 10 mA
Problem 5 of 10
A circuit's Thevenin equivalent is a 6 V source in series with 1.5 kΩ. What is the current of its Norton equivalent, in milliamps?
Show the working
- The Norton current is the short-circuit current at the output: IN = Vth over Rth.
- IN = 6 V over 1.5 kΩ = 4 mA, in parallel with the same 1.5 kΩ.
Answer: 4 mA
Problem 6 of 10
Two 10 kΩ resistors divide 15 V, and the output is taken through a 2.2 kΩ resistor from their midpoint. What is the Thevenin resistance at the output, in kilohms?
Show the working
- With the 15 V source short-circuited, the two 10 kΩ resistors are in parallel: 5 kΩ.
- The 2.2 kΩ is in series with that, on the way out.
- Rth = 5 kΩ + 2.2 kΩ = 7.2 kΩ
Answer: 7.2 kΩ
Problem 7 of 10
A sensor's output reads 8 V with nothing connected. With a 2 kΩ load it drops to 6 V. What is its Thevenin resistance?
Show the working
- With nothing connected no current flows, so Vth = 8 V.
- With the load, I = 6 V over 2 kΩ = 3 mA, and the missing 8 V − 6 V = 2 V is lost across Rth.
- Rth = 2 V over 0.003 A ≈ 667 Ω
Answer: 667 Ω
Problem 8 of 10
A source's Thevenin equivalent is a 10 V source in series with 50 Ω. What is the most power it can deliver to a load resistor?
Show the working
- Maximum power transfer: the load gets the most power when Rload = Rth = 50 Ω.
- Then half of Vth is across the load: 5 V, and I = 10 V over 100 Ω = 0.1 A.
- P = 5 V × 0.1 A = 0.5 W. The same again is lost in Rth.
Answer: 0.5 W
Problem 9 of 10
Stretch: a 9 V battery feeds node A through 1 kΩ, and a 6 V battery feeds node A through 2 kΩ. Both batteries' − terminals go to ground. What current flows into a 2 kΩ load connected from A to ground, in milliamps?
Show the working
- With no load, one current flows round the loop: 9 V − 6 V over 1 kΩ + 2 kΩ = 1 mA, from the 9 V battery into the 6 V one.
- So Vth = 9 V − 1 mA × 1 kΩ = 8 V. With both batteries short-circuited, Rth = 1 kΩ ∥ 2 kΩ ≈ 0.667 kΩ.
- I = 8 V over 0.667 kΩ + 2 kΩ = 8 V over 2.667 kΩ = 3 mA
Answer: 3 mA
Problem 10 of 10
Stretch: two 1 kΩ resistors divide 12 V. What is the most power the divider's output can deliver to a load resistor, in milliwatts?
Show the working
- Thevenin first: Vth = 6 V and Rth = 1 kΩ ∥ 1 kΩ = 500 Ω.
- The best load matches Rth: 500 Ω, which gets half of Vth, 3 V.
- P = V² over R = (3 V)² over 500 Ω = 0.018 W, which is 18 mW.
Answer: 18 mW
“Voltage dividers” is lesson 7 of 7 in Junction City, Electronics World 2. Free with an account. Lessons unlock in order, so you’ll do the 13 before it first.
Free lesson
Now build it yourself
Each lesson comes in three short parts: see the idea, try it on a live board, then build it yourself, with quick checks as you go.
“Voltage dividers” is lesson 7 of 7 in Junction City, Electronics World 2. Free with an account. Lessons unlock in order, so you’ll do the 13 before it first.
Or start from the very first lesson, no account neededCheck it with a calculator
The ideas behind it
- Thevenin's theorem explainedAny network of sources and resistors, seen from two terminals, is one source in series with one resistor.
- Voltage divider explainedTwo resistors that split a voltage: the formula, potentiometers, and why a load pulls the output down.
- How to calculate equivalent resistanceShrink any series-parallel network to one resistor, one step at a time, and spot what's really in parallel.
- Impedance matching explainedA load takes the most power when its resistance equals the source's: why radio is 50 Ω, and how to match.
Questions people ask
How do you find the Thevenin resistance?
Short-circuit every independent voltage source and open-circuit every independent current source, then work out the resistance you'd measure between the two output terminals. For a divider, that's R1 ∥ R2. If you can measure instead: R_th = V_open ÷ I_short, or use the drop a known load causes.
What is the difference between Thevenin and Norton?
They're the same circuit drawn two ways. Thevenin is a voltage source V_th in series with R_th. Norton is a current source I_N = V_th ÷ R_th in parallel with the same R_th. Any load behaves identically on either.
Does maximum power transfer mean maximum efficiency?
No. With R_load = R_th, the load gets the most power it can, but just as much is wasted in R_th, so the efficiency is only 50%. RF stages and antennas match on purpose. Audio amplifiers and power supplies keep R_th far below the load instead.
More practice
- Ohm's law practice problemsFind V, I or R, then the power, with the working for each.
- Units and prefixes practice problemsConvert mA, kΩ, µF, nF, pF, ms and mV, with the working for each.
- LED resistor practice problemsSize the resistor for one LED or a string, round to a standard value, check the power.
- Electrical power practice problemsPower three ways, energy in kWh, battery life and running costs, all worked.
- Series and parallel resistors practice problemsTotals in series and parallel, mixed networks and branch currents, all worked.
- Kirchhoff's laws practice problemsBalance currents at a junction and voltages round a loop, with the working for each.
- Voltage divider practice problemsFind Vout, pick R2 for a target and work out loading, with the working for each.
- Capacitor practice problemsCharge, capacitance, series and parallel, and stored energy, with the working.
- RC time constant practice problemsτ = R × C, the 63% rule, charging and discharging, with the working.
- Inductor practice problemsV = L × ΔI ÷ Δt, stored energy and inductors in series and parallel, with the working.
- RL circuit time constant practice problemsτ = L ÷ R, the current's rise and decay, and inductive kickback, with the working.
- AC voltage and transformer practice problemsPeak, RMS, period, AC power and transformer turns ratios, with the working.
- Capacitive and inductive reactance practice problemsCapacitive and inductive reactance, AC current and impedance, with the working.
- Impedance practice problems for RC and RL circuitsSeries RC and RL impedance, phase angle and current, with the working.
- RC filter practice problemsCutoff frequency, choosing R or C, and the output either side of the cutoff, with the working.
- Decibel practice problemsRatios to dB and back, for power and voltage, gains that add and the −3 dB point.
- LC resonance practice problemsf₀ = 1 ÷ (2π√(LC)), tuning for a frequency, and scaling, with the working.
- Diode practice problemsForward voltage, series resistor current, diodes in series, reverse bias and power dissipation.
- Rectifier and ripple practice problemsPeak output, ripple and the smoothing capacitor for half-wave and bridge rectifiers.
- Zener diode practice problemsSize a Zener regulator's resistor, split its current and check the Zener's power.
- Transistor switch practice problemsBase current, base resistor and load current for a BJT switch, then a MOSFET.
- MOSFET switch practice problemsConduction loss from R_DS(on), gate and pull-down currents, flyback diodes and junction temperature.
- Op-amp gain practice problemsInverting and non-inverting gain, the output, the resistor to pick and when it clips.
- Inverting and summing amplifier practice problemsInverting gain, input resistance, summing amps, averaging, a simple DAC and clipping.
- Schmitt trigger and hysteresis practice problemsHysteresis band, both thresholds and the feedback resistor for a comparator.
- Op-amp limits practice problemsGain-bandwidth, slew rate, output swing and input offset, with the working.
- Binary and hex practice problemsBinary to decimal and back, bits needed, the largest n-bit number and hex.
- Logic gates practice problemsGate outputs, truth-table rows, Boolean expressions and fewer gates, with the working.
- Counters and flip-flops practice problemsTop count, flip-flops needed, frequency division, rollover and ripple delay.
- PWM and duty cycle practice problemsDuty cycle, average voltage, on-time, analogWrite 0–255 and power, with the working.
- ADC and analog input practice problemsanalogRead to volts and back, resolution, dividers and 12-bit ADCs, with the working.