Practice problems
Rectifier and ripple practice problems
A rectifier converts AC into unidirectional (DC) current, and a smoothing capacitor holds the voltage up between the peaks. These ten problems go from an RMS voltage to the DC peak, subtract the diode forward voltages, find the ripple and size the capacitor, then check the reverse voltage each diode must block. Type your answer to check it, and open the working whenever you want it.
The method
- One 0.7 V drop for a half-wave rectifier, two (1.4 V) for a bridge
- The ripple frequency fr is twice the mains for a bridge (100 or 120 Hz), and the mains itself for half-wave
- To size the capacitor, rearrange it: C = I ÷ (fr × ΔV), then round up
- Each diode must block about one peak in a bridge, and about two peaks in a smoothed half-wave rectifier
ΔV is the peak-to-peak ripple. Work in amps and farads: 4700 µF is 0.0047 F.
The problems
Type your answer and tap Check. Every one has the working, step by step.
Problem 1 of 10
A transformer's secondary voltage is 9 V RMS (a sine wave). What is its peak voltage?
Show the working
- For a sine wave, Vpeak = VRMS × √2, and √2 ≈ 1.414.
- Vpeak = 9 V × 1.414 ≈ 12.7 V
Answer: 12.7 V
Problem 2 of 10
A half-wave rectifier uses one silicon diode (0.7 V) on a 12 V RMS transformer. What is the peak of its output?
Show the working
- The transformer's peak is 12 V × 1.414 ≈ 16.97 V.
- A half-wave rectifier's current passes through one diode: 16.97 V − 0.7 V ≈ 16.3 V.
Answer: 16.3 V
Problem 3 of 10
A bridge rectifier of silicon diodes (0.7 V each) runs from a 15 V RMS transformer. What is the peak DC output?
Show the working
- The transformer's peak is 15 V × 1.414 ≈ 21.21 V.
- In a bridge the current passes through two diodes, so it loses 2 × 0.7 V = 1.4 V.
- 21.21 V − 1.4 V ≈ 19.8 V
Answer: 19.8 V
Problem 4 of 10
A bridge rectifier runs from 60 Hz mains. What is the frequency of the ripple on its smoothing capacitor?
Show the working
- A bridge (full-wave) rectifier conducts on both half-cycles, so the capacitor is recharged twice per mains cycle.
- fr = 2 × 60 Hz = 120 Hz. A half-wave rectifier would have 60 Hz ripple.
Answer: 120 Hz
Problem 5 of 10
A bridge rectifier on 50 Hz mains feeds a 500 mA load, smoothed by a 4700 µF capacitor. About what is the peak-to-peak ripple voltage?
Show the working
- A bridge on 50 Hz mains gives 100 Hz ripple. Use ΔV ≈ I over fr × C, in amps and farads.
- ΔV ≈ 0.5 A over 100 Hz × 0.0047 F ≈ 1.06 V
Answer: 1.06 V
Problem 6 of 10
A bridge rectifier on 60 Hz mains must feed 1.2 A with no more than 1.5 V of peak-to-peak ripple. What smoothing capacitance does it need, in microfarads?
Show the working
- Rearrange the ripple formula: C = I over fr × ΔV, with fr = 2 × 60 Hz = 120 Hz.
- C = 1.2 A over 120 Hz × 1.5 V ≈ 0.00667 F
- That's 6670 µF. Pick the next standard value up, 6800 µF, for a little less ripple.
Answer: 6670 µF
Problem 7 of 10
A bridge rectifier runs from a 12 V RMS transformer, with silicon diodes (0.7 V). About what peak reverse voltage must each diode block while it is reverse-biased?
Show the working
- The transformer's peak is 12 V × 1.414 ≈ 16.97 V.
- At the peak, each reverse-biased diode is across the output plus one conducting diode: (16.97 V − 1.4 V) + 0.7 V.
- That's 16.97 V − 0.7 V ≈ 16.3 V. Choose diodes rated well above it, like 50 V or more.
Answer: 16.3 V
Problem 8 of 10
Stretch: a 9 V RMS transformer feeds a bridge (two 0.7 V drops) on 50 Hz mains, with 2200 µF smoothing and a 400 mA load. What is the lowest output voltage, at the ripple trough?
Show the working
- The peak is 9 V × 1.414 − 1.4 V ≈ 12.73 V − 1.4 V = 11.33 V.
- The peak-to-peak ripple is ΔV ≈ 0.4 A over 100 Hz × 0.0022 F ≈ 1.82 V.
- The lowest point is 11.33 V − 1.82 V ≈ 9.51 V.
Answer: 9.51 V
Problem 9 of 10
Stretch: a half-wave rectifier with a smoothing capacitor runs from a 12 V RMS transformer through one silicon diode (0.7 V). What is the peak reverse voltage across the diode?
Show the working
- The capacitor charges to the peak minus one drop: 16.97 V − 0.7 V ≈ 16.27 V, and holds it.
- Half a cycle later the secondary reaches its negative peak, −16.97 V, so the diode has the charged capacitor on its cathode and the negative peak on its anode.
- PIV ≈ 16.27 V + 16.97 V ≈ 33.2 V, about twice the peak. A bridge's diodes only see about one peak.
Answer: 33.2 V
Problem 10 of 10
Stretch: a 12 V RMS transformer feeds a bridge (two 0.7 V drops) on 50 Hz mains, and a 300 mA load must never see less than 12 V. What is the smallest smoothing capacitor, in microfarads?
Show the working
- The peak is 12 V × 1.414 − 1.4 V ≈ 15.57 V, so the ripple may be at most 15.57 V − 12 V = 3.57 V.
- C = I over fr × ΔV = 0.3 A over 100 Hz × 3.57 V ≈ 0.00084 F
- That's 840 µF. Round up to 1000 µF, which gives 3 V of ripple and a 12.6 V low point.
Answer: 840 µF
“Rectifiers” is lesson 2 of 6 in Silicon Ridge, Electronics World 5. Free with an account. Lessons unlock in order, so you’ll do the 29 before it first.
Free lesson
Now build it yourself
Each lesson comes in three short parts: see the idea, try it on a live board, then build it yourself, with quick checks as you go.
“Rectifiers” is lesson 2 of 6 in Silicon Ridge, Electronics World 5. Free with an account. Lessons unlock in order, so you’ll do the 29 before it first.
Or start from the very first lesson, no account neededThe ideas behind it
- Half-wave vs full-wave bridge rectifiersFour diodes that turn AC into DC, a capacitor that smooths it, and how to size it for your ripple.
- AC voltage and RMS explainedPeak, period, frequency and RMS: the numbers that describe an AC sine wave.
- How does a capacitor work?Two plates and a gap: how a capacitor stores charge and energy, and why it blocks steady DC.
Questions people ask
Why is a bridge rectifier's output 1.4 V below the peak?
On either half-cycle, the current passes through two of the bridge's four diodes on its way through the load, and each drops about 0.7 V. A half-wave rectifier uses one diode, so it loses only 0.7 V, but it discards every other half-cycle.
What ripple frequency do I use in ΔV ≈ I ÷ (f × C)?
The frequency at which the capacitor is recharged. A bridge or other full-wave rectifier recharges it on every half-cycle, so the ripple is at twice the mains frequency: 100 Hz on 50 Hz mains, 120 Hz on 60 Hz. A half-wave rectifier recharges once a cycle, at the mains frequency, so for the same C and load it has twice the ripple.
How do I size a smoothing capacitor?
Decide how much peak-to-peak ripple the load can tolerate, then use C = I ÷ (f × ΔV), with the current in amps and the answer in farads. Round up to the next standard value, and pick a voltage rating well above the peak, like 25 V for a 16 V output.
What is PIV for a rectifier diode?
Peak inverse voltage: the maximum reverse voltage a diode has to block. In a bridge it's about the transformer's peak. In a half-wave rectifier with a smoothing capacitor it's about twice the peak. Choose a diode rated comfortably above it.
More practice
- Ohm's law practice problemsFind V, I or R, then the power, with the working for each.
- Units and prefixes practice problemsConvert mA, kΩ, µF, nF, pF, ms and mV, with the working for each.
- LED resistor practice problemsSize the resistor for one LED or a string, round to a standard value, check the power.
- Electrical power practice problemsPower three ways, energy in kWh, battery life and running costs, all worked.
- Series and parallel resistors practice problemsTotals in series and parallel, mixed networks and branch currents, all worked.
- Kirchhoff's laws practice problemsBalance currents at a junction and voltages round a loop, with the working for each.
- Voltage divider practice problemsFind Vout, pick R2 for a target and work out loading, with the working for each.
- Thevenin and Norton equivalent practice problemsReduce a network to V_th in series with R_th, then load it, with the working.
- Capacitor practice problemsCharge, capacitance, series and parallel, and stored energy, with the working.
- RC time constant practice problemsτ = R × C, the 63% rule, charging and discharging, with the working.
- Inductor practice problemsV = L × ΔI ÷ Δt, stored energy and inductors in series and parallel, with the working.
- RL circuit time constant practice problemsτ = L ÷ R, the current's rise and decay, and inductive kickback, with the working.
- AC voltage and transformer practice problemsPeak, RMS, period, AC power and transformer turns ratios, with the working.
- Capacitive and inductive reactance practice problemsCapacitive and inductive reactance, AC current and impedance, with the working.
- Impedance practice problems for RC and RL circuitsSeries RC and RL impedance, phase angle and current, with the working.
- RC filter practice problemsCutoff frequency, choosing R or C, and the output either side of the cutoff, with the working.
- Decibel practice problemsRatios to dB and back, for power and voltage, gains that add and the −3 dB point.
- LC resonance practice problemsf₀ = 1 ÷ (2π√(LC)), tuning for a frequency, and scaling, with the working.
- Diode practice problemsForward voltage, series resistor current, diodes in series, reverse bias and power dissipation.
- Zener diode practice problemsSize a Zener regulator's resistor, split its current and check the Zener's power.
- Transistor switch practice problemsBase current, base resistor and load current for a BJT switch, then a MOSFET.
- MOSFET switch practice problemsConduction loss from R_DS(on), gate and pull-down currents, flyback diodes and junction temperature.
- Op-amp gain practice problemsInverting and non-inverting gain, the output, the resistor to pick and when it clips.
- Inverting and summing amplifier practice problemsInverting gain, input resistance, summing amps, averaging, a simple DAC and clipping.
- Schmitt trigger and hysteresis practice problemsHysteresis band, both thresholds and the feedback resistor for a comparator.
- Op-amp limits practice problemsGain-bandwidth, slew rate, output swing and input offset, with the working.
- Binary and hex practice problemsBinary to decimal and back, bits needed, the largest n-bit number and hex.
- Logic gates practice problemsGate outputs, truth-table rows, Boolean expressions and fewer gates, with the working.
- Counters and flip-flops practice problemsTop count, flip-flops needed, frequency division, rollover and ripple delay.
- PWM and duty cycle practice problemsDuty cycle, average voltage, on-time, analogWrite 0–255 and power, with the working.
- ADC and analog input practice problemsanalogRead to volts and back, resolution, dividers and 12-bit ADCs, with the working.