Practice problems
RL circuit time constant practice problems
An inductor switched onto a supply doesn't reach its full current at once: the current rises exponentially with the time constant τ = L ÷ R. These ten problems find τ and the final current, read the rise and decay after a few time constants, work out the inductive kickback when the current is interrupted and finish with a relay's pull-in time. Type your answer to check it, and open the working whenever you want it.
The method
- Rtotal includes the coil's winding resistance. Henries over ohms gives seconds
- Each τ, the current covers 63% of the remaining difference to its final value: 63%, 86%, 95% after 1τ, 2τ, 3τ, and settled after about 5τ
- Rising: I = Ifinal × (1 − e−t/τ). Decaying: I = Istart × e−t/τ
- At switch-off the current continues through whatever is connected across the coil, so the kickback peak is V = I × R
The problems
Type your answer and tap Check. Every one has the working, step by step.
Problem 1 of 10
What is the time constant of a 100 mH inductor in series with 50 Ω (total resistance)?
Show the working
- Use τ = L over R in henries and ohms: 100 mH = 0.1 H.
- τ = 0.1 H over 50 Ω = 0.002 s, which is 2 ms.
Answer: 2 ms
Problem 2 of 10
A coil with 60 Ω of resistance in total is switched onto 12 V. What steady-state current does it reach, in milliamps?
Show the working
- Once the current stops changing, the coil induces no voltage, so only the resistance limits it.
- Ifinal = 12 V over 60 Ω = 0.2 A, which is 200 mA.
Answer: 200 mA
Problem 3 of 10
A 470 mH coil has 20 Ω of winding resistance and is in series with an 80 Ω resistor. What is the time constant?
Show the working
- Rtotal includes the coil's winding resistance: 20 Ω + 80 Ω = 100 Ω.
- τ = 0.47 H over 100 Ω = 0.0047 s, which is 4.7 ms.
Answer: 4.7 ms
Problem 4 of 10
An RL circuit has a steady-state current of 200 mA. What current is flowing one time constant after switch-on?
Show the working
- In each τ the current covers 63% of the remaining difference to its final value.
- I = 0.63 × 200 mA ≈ 126 mA. The exact share is 1 − e⁻¹ = 0.632, which gives 126.4 mA.
Answer: 126 mA
Problem 5 of 10
A 2 H coil with 400 Ω in total is switched onto a supply. About how long until its current reaches steady state?
Show the working
- τ = 2 H over 400 Ω = 0.005 s = 5 ms
- It is effectively at steady state (99.3%) after about 5τ: 5 × 5 ms = 25 ms.
Answer: 25 ms
Problem 6 of 10
A coil carrying 80 mA is switched off and its current decays through a resistor. How much current is left after three time constants?
Show the working
- When decaying, about 5% of the current is left after 3τ (e⁻³ ≈ 0.05).
- I = 0.05 × 80 mA = 4 mA. The exact share, 0.0498, gives 3.98 mA.
Answer: 4 mA
Problem 7 of 10
You want a time constant of 0.1 ms with a 50 mH coil. What total series resistance do you need?
Show the working
- Rearrange τ = L over R: R = L over τ, with 0.1 ms = 0.0001 s.
- R = 0.05 H over 0.0001 s = 500 Ω
Answer: 500 Ω
Problem 8 of 10
A 0.4 H coil carries 150 mA when its switch opens. A 1 kΩ resistor is connected in parallel with the coil, and the coil's own resistance is negligible. What is the peak voltage across the coil?
Show the working
- The current in an inductor can't change instantly, so all 150 mA continues through the 1 kΩ resistor.
- V = I × R = 0.15 A × 1000 Ω = 150 V, then it decays with τ = 0.4 H over 1 kΩ = 0.4 ms.
Answer: 150 V
Problem 9 of 10
Stretch: a 0.5 H coil with 100 Ω in total is switched onto 12 V. What current flows 3 ms later, in milliamps?
Show the working
- Ifinal = 12 V over 100 Ω = 120 mA and τ = 0.5 H over 100 Ω = 5 ms.
- 3 ms isn't a whole number of τ, so use the exponential equation: I = Ifinal × (1 − e^(−t/τ)), with t over τ = 0.6 and e^(−0.6) ≈ 0.549.
- I = 120 mA × (1 − 0.549) = 120 mA × 0.451 ≈ 54.1 mA
Answer: 54.1 mA
Problem 10 of 10
Stretch: a relay coil of 0.2 H with 100 Ω in total runs from 12 V and pulls in at 90 mA. How long after switch-on does it pull in?
Show the working
- Ifinal = 12 V over 100 Ω = 120 mA and τ = 0.2 H over 100 Ω = 2 ms.
- 120 mA × (1 − e^(−t/τ)) = 90 mA, so e^(−t/τ) = 1 − 90 over 120 = 0.25.
- Take the natural log (the ln key): t = τ × ln 1 over 0.25 = 2 ms × ln 4.
- t = 2 ms × 1.386 ≈ 2.77 ms
Answer: 2.77 ms
“RL circuits” is lesson 5 of 5 in Capacitor Caves, Electronics World 3. Free with an account. Lessons unlock in order, so you’ll do the 19 before it first.
Free lesson
Now build it yourself
Each lesson comes in three short parts: see the idea, try it on a live board, then build it yourself, with quick checks as you go.
“RL circuits” is lesson 5 of 5 in Capacitor Caves, Electronics World 3. Free with an account. Lessons unlock in order, so you’ll do the 19 before it first.
Or start from the very first lesson, no account neededCheck it with a calculator
The ideas behind it
Questions people ask
What is the time constant of an RL circuit?
τ = L ÷ R, in seconds when L is in henries and R in ohms. R is the total resistance in the loop, including the coil's winding resistance. In one τ the current covers 63% of the remaining difference to its final value, and it reaches steady state after about 5τ.
Why does more resistance make an RL circuit faster?
R divides in τ = L ÷ R, where it multiplies in an RC circuit's τ = R × C. The current always starts rising at the same rate, V ÷ L, but more resistance means a lower final current, V ÷ R, so it gets there sooner. The price is less current, which is why L/R stepper-motor drives raise the supply voltage too.
What sets the final current in an RL circuit?
Only the voltage and the total resistance: I_final = V ÷ R_total. Once the current stops changing, the coil induces no voltage and acts like a length of wire. The inductance sets how long it takes to get there, not where it ends up.
More practice
- Ohm's law practice problemsFind V, I or R, then the power, with the working for each.
- Units and prefixes practice problemsConvert mA, kΩ, µF, nF, pF, ms and mV, with the working for each.
- LED resistor practice problemsSize the resistor for one LED or a string, round to a standard value, check the power.
- Electrical power practice problemsPower three ways, energy in kWh, battery life and running costs, all worked.
- Series and parallel resistors practice problemsTotals in series and parallel, mixed networks and branch currents, all worked.
- Kirchhoff's laws practice problemsBalance currents at a junction and voltages round a loop, with the working for each.
- Voltage divider practice problemsFind Vout, pick R2 for a target and work out loading, with the working for each.
- Thevenin and Norton equivalent practice problemsReduce a network to V_th in series with R_th, then load it, with the working.
- Capacitor practice problemsCharge, capacitance, series and parallel, and stored energy, with the working.
- RC time constant practice problemsτ = R × C, the 63% rule, charging and discharging, with the working.
- Inductor practice problemsV = L × ΔI ÷ Δt, stored energy and inductors in series and parallel, with the working.
- AC voltage and transformer practice problemsPeak, RMS, period, AC power and transformer turns ratios, with the working.
- Capacitive and inductive reactance practice problemsCapacitive and inductive reactance, AC current and impedance, with the working.
- Impedance practice problems for RC and RL circuitsSeries RC and RL impedance, phase angle and current, with the working.
- RC filter practice problemsCutoff frequency, choosing R or C, and the output either side of the cutoff, with the working.
- Decibel practice problemsRatios to dB and back, for power and voltage, gains that add and the −3 dB point.
- LC resonance practice problemsf₀ = 1 ÷ (2π√(LC)), tuning for a frequency, and scaling, with the working.
- Diode practice problemsForward voltage, series resistor current, diodes in series, reverse bias and power dissipation.
- Rectifier and ripple practice problemsPeak output, ripple and the smoothing capacitor for half-wave and bridge rectifiers.
- Zener diode practice problemsSize a Zener regulator's resistor, split its current and check the Zener's power.
- Transistor switch practice problemsBase current, base resistor and load current for a BJT switch, then a MOSFET.
- MOSFET switch practice problemsConduction loss from R_DS(on), gate and pull-down currents, flyback diodes and junction temperature.
- Op-amp gain practice problemsInverting and non-inverting gain, the output, the resistor to pick and when it clips.
- Inverting and summing amplifier practice problemsInverting gain, input resistance, summing amps, averaging, a simple DAC and clipping.
- Schmitt trigger and hysteresis practice problemsHysteresis band, both thresholds and the feedback resistor for a comparator.
- Op-amp limits practice problemsGain-bandwidth, slew rate, output swing and input offset, with the working.
- Binary and hex practice problemsBinary to decimal and back, bits needed, the largest n-bit number and hex.
- Logic gates practice problemsGate outputs, truth-table rows, Boolean expressions and fewer gates, with the working.
- Counters and flip-flops practice problemsTop count, flip-flops needed, frequency division, rollover and ripple delay.
- PWM and duty cycle practice problemsDuty cycle, average voltage, on-time, analogWrite 0–255 and power, with the working.
- ADC and analog input practice problemsanalogRead to volts and back, resolution, dividers and 12-bit ADCs, with the working.