Practice problems
Diode practice problems
A diode conducts in one direction (forward-biased) and blocks current in the other (reverse-biased). Once it conducts, it drops a roughly fixed forward voltage (VF) and leaves the rest of the supply for everything else. These ten problems subtract VF from the supply, find the current through a resistor, put diodes in series and work out a diode's power dissipation. Type your answer to check it, and open the working whenever you want it.
The method
- Use VF ≈ 0.7 V for silicon, 0.2 to 0.3 V for a Schottky, and the LED's own forward voltage for an LED
- Forward voltages in series add: subtract them all from the supply, then use Ohm's law on the resistor, I = VR ÷ R
- Reverse-biased, a diode blocks: no current, so the whole supply appears across it
- A diode's power dissipation is P = VF × I
The problems
Type your answer and tap Check. Every one has the working, step by step.
Problem 1 of 10
A lamp runs from a 9 V battery through a silicon diode with a forward voltage of 0.7 V. What voltage is across the lamp?
Show the working
- Once it conducts, the diode drops its forward voltage VF and the load gets the rest: Vload = Vsupply − VF.
- Vload = 9 V − 0.7 V = 8.3 V
Answer: 8.3 V
Problem 2 of 10
A device runs from a 5 V USB supply through a Schottky diode with a forward voltage of 0.3 V. What voltage reaches the device?
Show the working
- A Schottky diode's forward voltage is only about 0.2 to 0.3 V, which is why it's used where every volt counts.
- 5 V − 0.3 V = 4.7 V
Answer: 4.7 V
Problem 3 of 10
A silicon diode is connected in reverse (cathode to the battery's +), in series with a 1 kΩ resistor across a 9 V battery. What voltage is across the diode?
Show the working
- The diode is reverse-biased, so it blocks: only a negligible leakage current flows.
- With no current, the resistor drops I × R = 0 × 1 kΩ, nothing at all.
- So the full reverse voltage appears across the diode: 9 V. Its reverse voltage rating (VRRM) must exceed this.
Answer: 9 V
Problem 4 of 10
A silicon diode (0.7 V) and a 470 Ω resistor sit in series on a 12 V supply. What current flows?
Show the working
- The diode drops 0.7 V, so the resistor has 12 V − 0.7 V = 11.3 V.
- I = 11.3 V over 470 Ω ≈ 0.024 A, which is 24 mA.
Answer: 24 mA
Problem 5 of 10
Three silicon diodes, each with a 0.7 V forward voltage, sit in series with a 1 kΩ resistor on 5 V. What current flows?
Show the working
- Forward voltages in series add: 3 × 0.7 V = 2.1 V.
- The resistor has 5 V − 2.1 V = 2.9 V across it.
- I = 2.9 V over 1 kΩ = 2.9 mA. Volts divided by kilohms gives milliamps.
Answer: 2.9 mA
Problem 6 of 10
A silicon rectifier diode carries 1.5 A. At that current its forward voltage is 0.8 V, not 0.7 V. How much power does it dissipate?
Show the working
- A diode's power dissipation is its forward voltage times its current: P = VF × I.
- P = 0.8 V × 1.5 A = 1.2 W. That needs a diode rated above 1.5 A, such as a 3 A 1N5400, with heat conducted away through its leads into the board.
Answer: 1.2 W
Problem 7 of 10
A blue LED (3.2 V) and a 100 Ω resistor run from 5 V, with a silicon diode (0.7 V) in series to protect against a reversed supply. What current flows?
Show the working
- Subtract the series forward voltages first: 0.7 V + 3.2 V = 3.9 V.
- The resistor has 5 V − 3.9 V = 1.1 V across it.
- I = 1.1 V over 100 Ω = 0.011 A, which is 11 mA.
Answer: 11 mA
Problem 8 of 10
A red LED (2.0 V) runs from 9 V with a silicon protection diode (0.7 V) in series. What resistor gives exactly 15 mA?
Show the working
- The two forward voltages add: 2.0 V + 0.7 V = 2.7 V, so the resistor has 9 V − 2.7 V = 6.3 V.
- R = 6.3 V over 0.015 A = 420 Ω. That isn't an E12 value, so round up to 470 Ω, which gives about 13.4 mA.
Answer: 420 Ω
Problem 9 of 10
Stretch: a device draws 200 mA through a reverse-polarity protection diode. How much less power, in milliwatts, is dissipated with a 0.3 V Schottky than with a 0.7 V silicon diode?
Show the working
- Silicon: P = 0.7 V × 200 mA = 140 mW. Schottky: P = 0.3 V × 200 mA = 60 mW.
- The difference is 140 mW − 60 mW = 80 mW. Volts times milliamps gives milliwatts.
Answer: 80 mW
Problem 10 of 10
Stretch: three 1.5 V cells in series (4.5 V) drive a motor that behaves as a 30 Ω resistance, through a silicon diode with a 0.7 V forward voltage. What percentage of the battery's power is dissipated in the diode?
Show the working
- The motor has 4.5 V − 0.7 V = 3.8 V across it, so I = 3.8 V over 30 Ω ≈ 127 mA.
- The same current flows through the diode and the battery, so the power share is just the ratio of the voltages: 0.7 V over 4.5 V.
- 0.7 over 4.5 ≈ 0.156, so 15.6% of the battery's power is dissipated as heat in the diode. A 0.3 V Schottky would cut that to under 7%.
Answer: 15.6%
“Diodes” is lesson 1 of 6 in Silicon Ridge, Electronics World 5. Free with an account. Lessons unlock in order, so you’ll do the 28 before it first.
Free lesson
Now build it yourself
Each lesson comes in three short parts: see the idea, try it on a live board, then build it yourself, with quick checks as you go.
“Diodes” is lesson 1 of 6 in Silicon Ridge, Electronics World 5. Free with an account. Lessons unlock in order, so you’ll do the 28 before it first.
Or start from the very first lesson, no account neededCheck it with a calculator
The ideas behind it
- How does a diode work?A one-way valve for current: anode, cathode, the 0.7 V forward voltage and Schottky diodes.
- Schottky diode vs silicon diode: which should you use?Half the forward drop and half the heat, paid for in leakage and voltage rating.
- Reverse polarity protection explainedStop a backwards battery wrecking a circuit: the simple diode, and the MOSFET trick that costs almost nothing.
Questions people ask
What forward voltage should I use for a diode?
About 0.7 V for a silicon diode like the 1N4148 or 1N4001, and 0.2 to 0.3 V for a Schottky. LEDs have a much higher forward voltage: about 2.0 V for red and 3.2 V for blue or white. At large currents the forward voltage rises, often to 0.8 V or more for silicon, so check the datasheet's graph when it matters.
Does a reverse-biased diode let any current through?
Only a tiny leakage current, nanoamps for small-signal silicon diodes, up to microamps for rectifiers like the 1N4001, and more for a Schottky. For circuit problems, treat it as an open circuit: no current, so any resistor in series drops nothing and the full supply voltage appears across the diode.
Why not just put a diode straight across a battery?
Forward-biased, a diode is nearly a short circuit. Nothing in the loop limits the current, so it rises until the diode or the battery overheats. A diode always needs a load or a resistor in series to set the current.
More practice
- Ohm's law practice problemsFind V, I or R, then the power, with the working for each.
- Units and prefixes practice problemsConvert mA, kΩ, µF, nF, pF, ms and mV, with the working for each.
- LED resistor practice problemsSize the resistor for one LED or a string, round to a standard value, check the power.
- Electrical power practice problemsPower three ways, energy in kWh, battery life and running costs, all worked.
- Series and parallel resistors practice problemsTotals in series and parallel, mixed networks and branch currents, all worked.
- Kirchhoff's laws practice problemsBalance currents at a junction and voltages round a loop, with the working for each.
- Voltage divider practice problemsFind Vout, pick R2 for a target and work out loading, with the working for each.
- Thevenin and Norton equivalent practice problemsReduce a network to V_th in series with R_th, then load it, with the working.
- Capacitor practice problemsCharge, capacitance, series and parallel, and stored energy, with the working.
- RC time constant practice problemsτ = R × C, the 63% rule, charging and discharging, with the working.
- Inductor practice problemsV = L × ΔI ÷ Δt, stored energy and inductors in series and parallel, with the working.
- RL circuit time constant practice problemsτ = L ÷ R, the current's rise and decay, and inductive kickback, with the working.
- AC voltage and transformer practice problemsPeak, RMS, period, AC power and transformer turns ratios, with the working.
- Capacitive and inductive reactance practice problemsCapacitive and inductive reactance, AC current and impedance, with the working.
- Impedance practice problems for RC and RL circuitsSeries RC and RL impedance, phase angle and current, with the working.
- RC filter practice problemsCutoff frequency, choosing R or C, and the output either side of the cutoff, with the working.
- Decibel practice problemsRatios to dB and back, for power and voltage, gains that add and the −3 dB point.
- LC resonance practice problemsf₀ = 1 ÷ (2π√(LC)), tuning for a frequency, and scaling, with the working.
- Rectifier and ripple practice problemsPeak output, ripple and the smoothing capacitor for half-wave and bridge rectifiers.
- Zener diode practice problemsSize a Zener regulator's resistor, split its current and check the Zener's power.
- Transistor switch practice problemsBase current, base resistor and load current for a BJT switch, then a MOSFET.
- MOSFET switch practice problemsConduction loss from R_DS(on), gate and pull-down currents, flyback diodes and junction temperature.
- Op-amp gain practice problemsInverting and non-inverting gain, the output, the resistor to pick and when it clips.
- Inverting and summing amplifier practice problemsInverting gain, input resistance, summing amps, averaging, a simple DAC and clipping.
- Schmitt trigger and hysteresis practice problemsHysteresis band, both thresholds and the feedback resistor for a comparator.
- Op-amp limits practice problemsGain-bandwidth, slew rate, output swing and input offset, with the working.
- Binary and hex practice problemsBinary to decimal and back, bits needed, the largest n-bit number and hex.
- Logic gates practice problemsGate outputs, truth-table rows, Boolean expressions and fewer gates, with the working.
- Counters and flip-flops practice problemsTop count, flip-flops needed, frequency division, rollover and ripple delay.
- PWM and duty cycle practice problemsDuty cycle, average voltage, on-time, analogWrite 0–255 and power, with the working.
- ADC and analog input practice problemsanalogRead to volts and back, resolution, dividers and 12-bit ADCs, with the working.